Indiańskie forum

Forum o Indianach
Dzisiaj jest 09 grudnia 2019 19:36

Strefa czasowa UTC+1godz. [letni]

Nowy temat Odpowiedz w temacie  [ Posty: 1 ] 
Autor Wiadomość
 Tytuł: Wire Winding Machine factory
PostWiadomość wysłana.: 23 sierpnia 2018 11:09 

Rejestracja: 23 sierpnia 2018 10:51
Posty: 10
Płeć: Nie określono
WDTFRS-01 wind wire on mica sheet Winder. mica band winding machine

•Continuous winding operation with variable pitch on continuous lengths of round core material. Special pre-load settings for tightly wound Coils (droop test).
•Base material (core) can range from .06" to .008".
•Complete programmable touch screen controls.
•Winding speed up to 3000 RPM.
•Linear winding speeds up to 180" per minute.
•Easy to use, very user friendly.
Spindle No.1
Winding speed0-1200rpm (customizable)
Winding wire diameter0.1-1.5mm(AWG38-15)
Winding coil diameter0-220mm(8.6inch)
Winding width0-500/750/1000/1500/1800mm(70inch)
Power220v/50-60Hz (customizable)
Dimension1700*350*480mm((wind 1000MM length product machine)
Weight220KG(wind 1000MM length product machine)
Winding machine advantages
1. The use of independent bearing design, toothed belt replacement quick and easy.
2. Power-off save winding data, effectively avoid scrap coil.
3. wind to bobbin end side, intelligent deceleration, can fast winding thick wire.
4. Machine can automatic measure out the start winding data and winding width.
5. Can set the spindle climb time, you can set the winding speed up and down when the machine winding.
6. Full-English touch screen display, the operation more convenient and quick.
7. Using 32-bit ARM control chip controller, faster computing speed, effectively reducing the cable error.
8. All optical input and output isolation, work stability.
9. The use of Japan imported bearings, belts, Taiwan imported inverter and screw to ensure stable performance.

Scope of application:
Suitable for heating wire, resistance wire, mica sheet around the heating wire,mica band heating wire winding, Porcelain tube winding , and all longer coil products.

Although their purpose was to wind tiny heater core coils, this same method is also used to wind similar coils such as those used for medical catheters

You can see there is a drive shaft which transmits power to the opposing chuck.
This allows for the coordinated rotation of both ends of the wire mandrel under power.

The source spool of kanthal heater core wire is mounted on a constant tension dereeler device which is mounted directly to the traverse assembly.
The source spool traverses at the same rate as the coil as it is wound.
This allows the source kanthal wire to maintain a narrow angle to the mandrel wire

The demonstration machine is configured to wind a coil as long as 24 inches. The coil length can be a long as 39 inches with an optional extended traverse housing.

After the mandrel wire is fastened to the hand tightened drill chuck, a toggle switch operates an air cylinder which pulls the tailstock back to place tension on the mandrel wire between the two chucks.

When the coil is finished winding the toggle switch is again operated to push the tailstock in which releases tension on the mandrel wire so that the finished heater core coil can be slid off of the mandrel.

The machine can easily be converted to winding coils that only need a single powered spindle if winding needs change.Wire Winding Machine factory

Na górę  || 
 Wyświetl profil  
Bot Reklamowy Reklama
Na górę
Wyświetl posty nie starsze niż:  Sortuj wg  
Nowy temat Odpowiedz w temacie  [ Posty: 1 ] 

Strefa czasowa UTC+1godz. [letni]

Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 1 gość

Nie możesz tworzyć nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz dodawać załączników

Przejdź do:  
Technologię dostarcza phpBB® Forum Software © phpBB Group
Chronicles phpBB2 theme by Jakob Persson. Stone textures by Patty Herford.
With special thanks to RuneVillage